All Manuals Close Window

Specifications


Engine

Manufacturer Yanmar

Model Number 3TNV76

Type Diesel

Gross Horsepower 17.9 kW (24 hp)

PTO Horsepower 13.4 kW (18 hp)

Cylinders Three

Slow Idle Speed 1300 rpm

Rated Engine Speed 3000 rpm

High Idle Speed 3170 rpm

Operating Range 1270 - 3170 rpm

Cooling Type Liquid

Oil Filter Standard Single Element

Air Cleaner Dry Type, Two Stage

Drivetrain

Type 2 Range Hydrostatic

Number of Speeds Infinite

Mechanical Front Wheel Drive (MFWD) Standard

MFWD Capability All Ranges

MFWD Engagement On The Go

Final Drive Spur Gear

Rear Axle Maximum Load 1100 kg (2426 lb)

Front Axle Maximum Load 880 kg (1940 lb)

Electrical System

Type 12 Volt

Battery Size 500 Cold Cranking Amps @ -18?C (0?F)

Alternator 40 amp

Front Wheels and Tires

Standard 23x8.5-12 R4

Optional 23x8.5-12 R3

Rear Wheels and Tires

Standard 12-16.5 R4

Optional 31x13.5-15 R3

Front Tire Inflation Pressures (Maximum)

23x8.5-12 R3 152 kPa (22 psi)

23x8.5-12 R4 241 kPa (35 psi)

Rear Tire Inflation Pressures (Maximum)

31x13.5-15 R3 140 kPa (20 psi)

12-16.5 R4 276 kPa (40 psi)

Tire Loads

NOTE: Maximum load capacity for single tire.

Front (23x8.5-12 6PR R4) 667 kg (1471 lb)

Front (23x8.5-12 4PR R3) 506 kg (1116 lb)

Rear (12-16.5 6PR R4) 1914 kg (4220 lb)

Rear (31x13.5-15 4PR R3 TI) 839 kg (1850 lb)

Fluid Capacities

Fuel Tank 23 L (6.1 gal)

Cooling System 3.2 L (3.4 qt)

Crankcase with Filter 3.2 L (3.4 qt)

Transmission and Hydraulic System 10 L (2.6 gal)

Front Axle 3.4 L (3.6 qt)

Ground Speeds

NOTE: All ground speed calculations shown are with machine equipped with standard tires and operated at 2600 engine rpm.

Forward - Range High 0-18.2 km/h (0-11.3 mph)

Reverse - Range High 0-9.1 km/h (0-5.7 mph)

Forward and Reverse - Range Low 0-7.3 km/h (0-4.5 mph)

Dimensions

NOTE: Machine equipped with standard tires.

Wheelbase 1600 mm (63 in.)

Overall Length with 3-point Hitch 2774 mm (109.2 in.)

Overall Width (Minimum) 1188 mm (46.8 in.)

Tread Width @ Centerline (Minimum)

Front (Only Wide Position Recommended) 923 mm (36.3 in.)

Rear (Only Wide Position Recommended) 919 mm (36.2 in.)

Height From Ground

To Top of Hood 1208 mm (48 in.)

To Top of ROPS 2261 mm (89 in.)

Ground Clearance

Front Axle 320 mm (13 in.)

Rear Axle 260 mm (10.2 in.)

Turning Radius

With Brakes 2.0 m (6.7 ft.)

Without Brakes 2.3 m (7.7 ft.)

Weight

Machine equipped with a ROPS, 3-point hitch, standard tires and all fluids. 753 kg (1660 lb)

3-Point Hitch

Type Category 1

Lift Capacity-61 cm (24 in.) behind link arms 522 kg (1150 lb)

Lift Capacity-at link link ends 650 kg (1433 lb)

Torque Values

Metric Torque Values (Dry)

Class 7

Class 8.8

Class 10.9

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

M6

11

8.1

17

12.5

M8

29

21

35

26

41

30

M10

59

44

67

49

80

59

M12

98

72

113

83

132

97

M14

147

108

167

123

201

148

M16

206

152

• Use 80% of the value when tightening part is aluminum.

• Use 60% of the value for 4T bolts and lock nuts.


Inch Fastener Torque Values (Dry)

Grade 21

Grade 5

Grade 8

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

1/4

7.4

5.5

12

9

17

12.5

5/16

15

11

24

18

35

26

3/8

27

20

45

33

62

46

7/16

43

32

70

52

102

75

1/2

68

50

108

80

156

115

9/16

95

70

156

115

217

160

5/8

136

100

217

160

305

225

3/4

238

175

1

“Grade 2” applies for hex cap screws (not hex bolts) up to 152mm (6 in.) long.



Metric Torque Values (Lubricated)

Class 7

Class 8.8

Class 10.9

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

M6

9

6.6

13

9.6

M8

23

17

25

18.5

29

21.4

M10

44

33

51

38

61

45

M12

78

58

83

61

103

76

M14

118

87

127

94

152

112

M16

167

123

• Use 80% of the value when tightening part is aluminum.

• Use 60% of the value for 4T bolts and lock nuts.


Inch Fastener Torque Values (Lubricated)

Grade 21

Grade 5

Grade 8

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

1/4

6.1

4.5

9.5

7

13.6

10

5/16

12.2

9

20

15

28

21

3/8

22

16

35

26

49

36

7/16

35

26

56

41

79

58

1/2

53

39

85

63

122

90

9/16

76

56

122

90

176

130

5/8

106

78

170

125

217

160

3/4

190

140

1

“Grade 2” applies for hex cap screws (not hex bolts) up to 152mm (6 in.) long.