X590Riding Lawn Equipment

The tractor is powered by a John Deere iTorque™ power system, a combination of engine features and an exclusive hood design providing superior lugging ability, even cooling, and durability. Key engine features include:

• Large, 726-cc displacement
• 16.7 kW at 3250 rpm
• V-twin air-cooled design
  • Excellent power and performance
  • Smooth, quiet power
  • Easy starts
• Quality features include:
  • Cast-iron cylinder liners
  • Overhead valves
  • Full-pressure lubrication
  • Replaceable oil filter
  • Dual-stage air cleaner
• Solenoid-shift starter for easy starts, even in cold weather

• Electronic fuel injection (EFI)

  • EFI meters the correct amount of fuel directly into each engine cylinder for all operating conditions.
  • It simplifies engine starts and warm-up by eliminating the need for the operator to use a choke.
  • Fuel usage is reduced up to 10 percent compared to a carbureted engine.

• Constant-speed governor

  • Constant-speed governor works in conjunction with EFI to electronically adjust the supply of fuel air mixture, to increase torque as needed to maintain engine operating speed under load.
  • Ground speed and mower blade-tip speed remain constant, even in heavy-grass conditions, to improve productivity and cut quality.
    • Mechanical governors cannot respond fast enough to maintain a constant engine speed.
  • Some torque rise remains to warn the operator before the engine stalls.
  • X590's constant-speed governor is a first in the consumer mowing industry.

Electronic fuel injection and constant-speed governor

No choke control is needed for the EFI engine because a servo motor controls the intake air butterfly valve and the air stream. For cold starts the actuator will close the valve, making starting the engine easier - no choke lever is needed. Starts are quick and easy - even for inexperienced operators.

The advanced engine features provide the following advantages:

• Performance is improved.

  • Mowing time is reduced as the constant-speed governor keeps the engine operating at optimum speed, responding instantaneously as the mower transitions from light to heavy mowing.
  • Cut quality is improved, especially in difficult mowing conditions, because the constant-speed governor keeps the mower blades turning at full speed, delivering optimal cut quality and dispersion of clippings. While snow blowing, maintaining the fan speed enables consistent snow placement.

• Uptime is increased.

  • Fast, reliable starts are routine just like with a modern automobile. EFI automatically meters fuel, including the extra fuel needed to start a cold engine. Flooding by unnecessary choking of a warm engine is eliminated. No carburetor adjustments are needed at altitude.
  • No choke-related problems since the choke is eliminated, thus ensuring operator confidence and quick starts, even in cold ambient temperatures (snow blower use). The mechanical throttle cable is replaced by an electric linkage that is not susceptible to wear or freezing.

• Cost of ownership is reduced.

  • EFI precisely meters fuel to each engine cylinder. Fuel usage can be expected to be about 10 percent less than with a similar carbureted tractor.
  • Reduced maintenance expense because of fewer complaints related to hard starting, vapor lock, misfire, run-on, or fouled spark plugs.

• The X590 Tractor, including the engine, is covered by a 4-year/500-hour bumper-to-bumper warranty*.

Flywheel alternator

A flywheel alternator provides plenty of capacity to quickly recharge the battery and power electrical equipment, such as lights or a sprayer:

• 15-amp capacity
• Regulated to keep the battery at a full charge, without risk of overcharging

*Term limited to years or hours used, whichever comes first, and varies by model. See the LIMITED WARRANTY FOR NEW JOHN DEERE TURF AND UTILITY EQUIPMENT at JohnDeere.com or JohnDeere.ca/TUWarranty for details.

Fuel tank has a large, 16.7-L (4.4-U.S. gal.) capacity

Quality fuel system components enhance performance and convenience:

• Large, 16.7-L (4.4 U.S. gal.) capacity
• Wide, 7.6-cm (3-in.) diameter fuel tank filler opening
  • Located on the left fender
  • Makes adding fuel easy and helps eliminate spillage
• Sealed and tethered fuel cap
  • Reduced fuel vapor loss
  • Less chance of losing fuel cap

• Automotive-style fuel gauge on the dash
  • Easy to read from tractor seat
  • Reduces likelihood of running out of fuel
  • Eliminates unnecessary stops to refill

The 122-cm (48-in.) Accel Deep Mower Deck is a stamped-steel, deep, flat-top design that delivers excellent cut quality, productivity, cleanliness, durability, and versatility. Optimal performance and dispersion of clippings is provided, even at faster mowing speeds:

• 12.3-cm (4.83-in.) depth throughout the entire deck shell for optimum mowing, mulching, and bagging performance
• Stamped-steel design eliminates sharp edges and corners where material can build up and diminish mowing performance
• Mower deck is suspended from the vehicle for a smooth and level cut
  • Adjustable mower wheels, positioned just above ground level, help smooth out the mowing job

Excellent cut quality

Deep mower-deck stamping gives excellent cut quality. It allows the cut and suspended material room to exit the deck without getting recut:

• Reducing the amount of re-cutting enables more power to be used to cut incoming grass, which greatly improves mower capacity.
  • Helps maintain excellent cut quality at faster mowing speeds
• Clean flow of material out of discharge prevents cut material from interfering with cutting the incoming grass, making it possible for the blades to cut incoming material cleanly.
• Even in mulching mode, cut evenness is improved compared to other designs because the additional depth allows for continuous circulation, optimal re-cutting, and an even distribution of clippings.

Productivity - getting the job done fast

Deep mower-deck stamping gives high productivity which gets the job done fast. It allows the cut and suspended material room to exit the deck quickly, reducing the amount of re-cutting so more power is available to process incoming grass:

• Greatly improves mowers capacity to maintain excellent mowing performance in difficult mowing conditions and at higher speeds

Large discharge opening is both high and wide to handle more material:

• Gives a smooth, even discharge of clippings at all mowing speeds
• Reduces the chance of plugging, especially important when operating in wet, thick, or dense grass and when bagging 
• The 54A Power Flow blower runs faster, providing 20 percent more air than the 54X Power Flow blower.

Cleanliness - for the mower and the operator

The flat-top shape of the deck stamping is optimal for keeping itself and the operator clean:

• There are few places to catch and hold material on top and underneath the deck.
  • Top of deck stays cleaner, reducing time and effort needed for cleaning and service
  • Underside of deck is self-cleaning to maintain optimum performance without buildup of material to interfere with the flow of air and clippings
  • Less need to clean and remove buildup of material from underside deck
• The depth of the Accel Deep Mower Deck minimizes the amount of material that escapes from the front of the deck
  • Limited amount of material to drift onto the operator and mower deck
  • Even for material discharged out the chute, less re-cutting results in larger pieces that are less likely to end up on the operator
  • Mulching prevents the discharge of material completely and the MulchControl™ attachment makes mulching a practical solution for most mowing situations.

Cleaning a mower deck, both top and bottom, is one of the most frequent maintenance activities:

• The flat-top design reduces places for material to buildup and makes material that does collect easy to remove.
• Spring-loaded covers make spindle areas accessible for cleaning without any tools.

A wash port is provided to make cleaning the underside of the mower deck easy.

• A hose-end adapter for the appropriate water hose to be used can be purchased locally for connection to the wash port.

How MulchControl works

MulchControl is an innovative, simple design that is easy to use and maintain:

• The MulchControl attachment includes baffles to control the flow of material under the deck.
  • The left mower blade area is completely enclosed and optimized for mulching, thus will mulch even when the mower is in the side-discharge mode.
  • Baffles around the center and right blades are optimized for mulching when the discharge baffle is closed.

Superior durability is designed in

The 48A Mower Deck has strong spindle pockets, to keep the blades perfectly aligned, even after years of tough service:

• Ribs in the deck shell add strength where it is needed.
• The 48A has a 23 percent heavier overall weight than the Edge Xtra 122-cm (48-in.) Mower Deck.

Low-tension belt-drive design reduces the side load on engine lower bearings and mower deck bearings for longer life.

The 48A Mower Deck features a 16-mm (5/8-in.) diameter solid-steel rod side bumper that provides extra strength and protection.

Dual-stage E-coat and powder-paint coatings provide extra protection from rust.

Versatility - easy to change between side discharge, mulch, and bagging modes

The 48A Mower is designed for maximum versatility, providing the greatest ease in changing from one mower discharge mode to another:

• With the optional MulchControl attachment installed (along with the special mulching blades), changing from side-discharge to mulching or vice versa is done with the simple flip of a lever.
• The Power Flow rear bagger can be used with the MulchControl attachment and blades installed - by simply placing the MulchControl lever in the side discharge position.

MulchControl option

The MulchControl attachment for the 48A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:

• A beautiful looking lawn
• Grass clippings not blown onto the operator, driveways, or flower beds
• Less fertilizer use
• Elimination of the effort needed to dispose of clippings

• The MulchControl handle is located on top of the mower deck and used to open and close the discharge baffle.
• The operator is required to get off of the machine in order to engage or disengage mulch mode.
• Changing from mulching to side discharge or vice versa takes only a few seconds.

MulchControl is well-suited to the following mowing situations:

• Usually mulch, but side discharge when grass gets too long
• Usually side-discharge, but would like to be able to close the chute to control clippings
• Always mulch a main lawn, but often side discharge secondary lawns
• Bag clippings, but want to go farther before emptying bags

MulchControl puts the operator in control of the clippings. Now the operator can have all the benefits of mulching with the ability to easily change to side discharge or bagging when needed.

While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:

• When cutting strong southern grasses, such as Zoysia and Bermuda
• When cutting in wet, high-growth conditions, such as those found in the Pacific Northwest United States
• When optimum bagging and lawn clean up is desired

230 L (6.5 bu) Power Flow rear bagger

The 48A Power Flow blower is easy to install and easy to clean, as it pivots out from the mower for easy access.

The 137-cm (54-in.) Accel Deep Mower Deck is a stamped-steel, deep, flat-top design that delivers excellent cut quality, productivity, cleanliness, durability, and versatility. Optimal performance and dispersion of clippings is provided, even at faster mowing speeds:

• 12.3-cm (4.83-in.) deep throughout the entire deck shell for optimum mowing, mulching, and bagging performance
• Stamped-steel design eliminates sharp edges and corners where material can build up and diminish mowing performance
• Mower deck is suspended from the vehicle for a smooth and level cut
  • Adjustable mower wheels, positioned just above ground level, help smooth out the mowing job

Excellent cut quality

Deep mower-deck stamping gives excellent cut quality. It allows the cut and suspended material room to exit the deck without getting recut:

• Reducing the amount of re-cutting enables more power to be used to cut incoming grass, which greatly improves mower capacity.
  • Helps maintain excellent cut quality at faster mowing speeds
• Clean flow of material out of discharge prevents cut material from interfering with cutting the incoming grass, making it possible for the blades to cut incoming material cleanly.
• Even in mulching mode, cut evenness is improved compared to other designs because the additional depth allows for continuous circulation, optimal re-cutting, and an even distribution of clippings.

Productivity - getting the job done fast

Deep mower-deck stamping gives high productivity which gets the job done fast. It allows the cut and suspended material room to exit the deck quickly, reducing the amount of re-cutting so more power is available to process incoming grass:

• Greatly improves mowers capacity to maintain excellent mowing performance in difficult mowing conditions and at higher speeds

Large discharge opening is both high and wide to handle more material:

• Gives a smooth, even discharge of clippings at all mowing speeds
• Reduces the chance of plugging, especially important when operating in wet, thick, or dense grass and when bagging 
• The 54A Power Flow blower runs faster, providing 20 percent more air than the 54X Power Flow blower.

How MulchControl works

MulchControl is an innovative, simple design that is easy to use and maintain:

• The MulchControl attachment includes baffles to control the flow of material under the deck.
  • The left mower blade area is completely enclosed and optimized for mulching, thus will mulch even when the mower is in the side-discharge mode.
  • Baffles around the center and right blades are optimized for mulching when the discharge baffle is closed.

Cleanliness - for the mower and the operator

The flat-top shape of the deck stamping is optimal for keeping itself and the operator clean:

• There are few places to catch and hold material on top and underneath the deck.
  • Top of deck stays cleaner, reducing time and effort needed for cleaning and service
  • Underside of deck is self-cleaning to maintain optimum performance without buildup of material to interfere with the flow of air and clippings
  • Less need to clean and remove buildup of material from underside deck
• The depth of the Accel Deep Mower Deck minimizes the amount of material that escapes from the front of the deck
  • Limited amount of material to drift onto the operator and mower deck
  • Even for material discharged out the chute, less re-cutting results in larger pieces that are less likely to end up on the operator
  • Mulching prevents the discharge of material completely and the MulchControl™ attachment makes mulching a practical solution for most mowing situations.

Cleaning a mower deck, both top and bottom, is one of the most frequent maintenance activities:

• The flat-top design reduces places for material to build up and makes material that does collect easy to remove.
• Spring-loaded covers make spindle areas accessible for cleaning without any tools.

A wash port is provided to make cleaning the underside of the mower deck easy:

• A hose-end adapter for the appropriate water hose to be used can be purchased locally for connection to the wash port.

Superior durability is designed in

The 54A Mower Deck has strong spindle pockets, to keep the blades perfectly aligned, even after years of tough service:

• Ribs in the deck shell add strength where it is needed.
• The 54A has a 3 percent heavier overall weight than the Edge Xtra 137-cm (54-in.) Mower Deck.

Low-tension belt-drive design reduces the side load on engine lower bearings and mower deck bearings for longer life.

The 54A Mower Deck features a 16-mm (5/8-in.) diameter solid-steel rod side bumper that provides extra strength and protection.

Dual-stage E-coat and powder-paint coatings provide extra protection from rust.

Versatility - easy to change between side discharge, mulch, and bagging modes

The 54A Mower is designed for maximum versatility, providing the greatest ease in changing from one mower discharge mode to another:

• With the optional MulchControl attachment installed (along with the special mulching blades), changing from side-discharge to mulching or vice versa is done with the simple flip of a lever.
• The Power Flow Rear Bagger can be used with the MulchControl attachment and blades installed by simply placing the MulchControl lever in the side discharge position.

MulchControl option

The MulchControl attachment for the 54A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:

• A beautiful looking lawn
• Grass clippings not blown onto the operator, driveways, or flower beds
• Less fertilizer use
• Elimination of the effort needed to dispose of clippings

• The MulchControl handle is located on top of the mower deck and used to open and close the discharge baffle.
• The operator is required to get off of the machine in order to engage or disengage mulch mode.
• Changing from mulching to side discharge or vice versa takes only a few seconds.

MulchControl is well-suited to the following mowing situations:

• Usually mulch, but side discharge when grass gets too long
• Usually side-discharge, but would like to be able to close the chute to control clippings
• Always mulch a main lawn, but often side discharge secondary lawns
• Bag clippings, but want to go farther before emptying bags

MulchControl puts the operator in control of the clippings. Now the operator can have all the benefits of mulching with the ability to easily change to side discharge or bagging when needed.

While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:

• When cutting strong southern grasses, such as Zoysia and Bermuda
• When cutting in wet, high-growth conditions, such as those found in the Pacific Northwest United States
• When optimum bagging and lawn clean up is desired

230 L (6.5 bu) Power Flow rear bagger

The Power Flow blower is easy to install and easy to clean, as it swings out away from the mower for easy access.

Hydraulic power steering is standard equipment:

• Provides effortless automotive-like control
• Reduces operator fatigue and increases productivity
• Offers a tight turning radius for great maneuverability
• Adjustable-tilt steering wheel for optimum operator comfort

Convenient hydraulic lift

Convenient hydraulic-lift lever makes raising and lowering the mower or implement easy:

• The hydraulic-lift control lever is positioned on the dash near the steering wheel.
• Hydraulic lift provides quick, easy, and precise fingertip control of equipment.
• Implement float is built into the lift linkage.

The integrated hydrostatic transaxle (IHT) encloses the hydrostatic pump and motor rotating groups in the same housing with the differential and axle housing:

• Very efficient piston-type design
• Fewer sealing surfaces to minimize potential for leakage

When combined with the foot controls, the hydrostatic transmission functions similarly to that of an automatic transmission in an automobile, so the term automatic is often used to describe it.

Key features of the drive system are as follows:

• Large pump and motor rotating groups for long life and efficient operation
• Full-length axle housings to support heavy loads
• Twin Touch™ foot control for easy and precise change of speed and direction
• Internal wet-disk brake for long life and consistent operation
• Brake interlock system that returns the foot control pedals to neutral during panic stops
• Return mechanism that closes the freewheeling valve when the brake pedal is depressed to start the engine

Standard cruise control

Cruise control is standard equipment. It maintains a set tractor ground speed for mowing large areas or when driving the tractor from one location to another.

Traction assist (differential lock)

Traction assist is standard equipment:

• Traction assist supplies positive power to both drive wheels for increased traction.
• Foot-operated traction assist control is convenient for the operator to use, when needed.

Controls

The contoured dash has clean, attractive styling and ergonomic controls for easy use:

• Controls are color-coded for easy identification by the operator.
• Controls are logically placed and easy to reach.
• The power take-off (PTO) switch allows the operator to get fingers underneath it, like a T-handle, to pull up for easy activation.
• The reverse implement option (RIO) switch is an easy to see and use yellow button.
  • To simplify snow blower operation, RIO can be activated with the same hand that lifts or latches the snow blower.
• The latch control on foot-lift models and hydraulic-lift control on power-lift models and the park brake latch are pivot levers for low effort.
• Cruise control activation is handled by an automotive-style button.
• Separate engine speed and choke controls make starting and warming up the engine easier in cold weather.
  • The choke lever is spring loaded to eliminate the chance the tractor will be unintentionally operated with the choke partially closed.
• Functional design of the throttle and choke controls provides good appearance and a comfortable feel.

Display panel

		A — Caution / stop		H — Low engine oil pressure
		B — Power take-off (PTO)		I — Engine malfunction
		C — Battery charge status		J — Engine speed symbol
		D — Park brake		K — Engine speed
		E — Operator presence		L — Best cut range
		F — Hourmeter		M — Fuel gauge
		G — Service

Instrument display has the look and feel of a modern automobile. A power-up sequence cycles lights and gauges to indicate they are working:

• Display features dark-cockpit design to minimize operator distractions.
• Display is back lit for night visibility.
  • Night visibility is especially useful with snow blower use.
• Hourmeter makes it easy to tell when oil changes and other maintenance should be performed.
• Electronic fuel gauge provides real-time fuel level information.
• A tachometer graphically displays engine speed.
  • Target-zone graphics inform the operator of the engine speed range to use for best cut quality.
• An indicator tells the operator when the PTO is operating.
• Bright caution and stop lights capture the operator's attention when important information is on the instrument cluster.
  • Damage can be prevented and repair costs reduced by addressing problems early.
• Operators are advised of what the problem is if they attempt to operate the mower with unsatisfied PTO, seat, or park brake interlocks.
  • The indicators are also useful to identify the reasons the PTO or engine may have shut off when an interlock is unsatisfied.
• Operators are advised if battery voltage is low, normal, or excessive.
• The service indicator light illuminates to indicate a diagnostic error code is stored.
  • On-board diagnostics provides trouble codes for use by trained technicians.
    • For example, a technician will be able to test switch functionality and circuit continuity without tools.

Twin Touch™ foot control is easy to use and has cruise control

Twin Touch foot pedals control the speed and direction of travel:

• Automotive-type accelerator control ensures easy operation.
• Operator can change direction without lifting foot off the platform.
• Large pedal surface gives superior operator comfort.

Cruise control

Cruise control is standard equipment:

• To engage, push the cruise button and hold until the foot is removed from the forward pedal.
• For emergency stop, the cruise control can be released by pushing on the brake pedal or the forward pedal.

Mower deck height adjustment

A rotary dial knob makes adjusting the mower cut height quick and easy:

• Mower cut height can be adjusted in 6.4-mm (0.25-in.) increments from 2.5 cm to 10.2 cm (1 in. to 4 in.)
• Mower deck returns to the same preset height each time it is lowered.
• Onboard deck-leveling gauge and Exact Adjust tool conveniently located in the storage compartment under the seat
  • Used in conjunction with Exact Adjust ports for easy and accurate leveling of the mower deck for optimum mowing performance

Convenient hydraulic lift

Convenient hydraulic-lift lever makes raising and lowering the mower or implement easy:

• The hydraulic-lift control lever is positioned on the dash near the steering wheel.
• Hydraulic lift provides quick, easy, and precise fingertip control of equipment.
• Implement float is built into the lift linkage.

Parking brake control

Depressing brake pedal applies internal wet-disk brakes (which provide excellent durability and long life) for safe stopping.

Parking brake control is conveniently located for easy access; holds brake pedal securely in locked position.

Electric power take-off (PTO) clutch is easy and convenient to use

The heavy-duty electric PTO clutch is operated with a convenient dash-mounted switch.

Heavy-duty PTO clutch

The PTO clutch is designed to operate through many on/off cycles.

Reverse implement option (RIO) allows mowing while backing up if deemed necessary

Mowing while backing up is strongly discouraged.

An operator who deems it necessary and chooses to keep the mower engaged while backing up, must bring the vehicle to a stop, then push the yellow, RIO button as the reverse pedal is depressed slightly. The operator can then release the RIO button and the mower will continue to operate.

This procedure must be repeated the next time the operator chooses to keep the mower (or other PTO-operated equipment) engaged while backing up.

The frame is made of heavy-duty, formed steel, reinforced in critical areas and welded for even greater strength:

• Frame is formed from 12-gauge, 2.66-mm (0.105-in.) thick material.
• Rear hitch plate is formed from 6.4-mm (0.25-in.) steel and completes the frame assembly.
• Rear hitch plate can support up to four 19-kg (42-lb) Quik-Tatch weights.
• Standard front bumper can support up to four 19-kg (42-lb) Quik-Tatch weights.

Front axle and wheel spindles are heavy-duty

The front axle is made of nodular cast iron:

• Strong and shock resistant
• Will not yield under heavy loads or impact

Replaceable bushings are used at the center axle pivot and steering spindles:

• Provide excellent wear resistance
• Grease cavity between bushings maintains lubrication and easy steering between greasings
• Easy-to-service grease fittings at each spindle

Front steering spindles

The front steering spindles are strong for long life:

• Have the strength to handle heavy implements
  • 25.4-mm (1-in.) steering spindle diameter 
• Provide long life at bearing surfaces
  • 25.4-mm (1-in.) diameter front wheel bearings
• Sealed precision ball bearings at front wheels ensure long life and are maintenance free

Rear equipment-mounting system is heavy-duty for easy installation of a variety of equipment

A heavy-duty equipment mounting system is used:

• Includes strong frame mounts with a combination of mounting holes in the tractor hitch plate that accept pins or shoulder bolts to support heavy, rear-mounted equipment
• Easily attach optional equipment to the tractor
• Can bear the load of heavy, rear-mounted equipment, such as material collection systems

Smooth, rounded contours present a modern, stylish appearance:

• Hood styling incorporates efficient full-length air-intake louvers on each side.
  • Cooler engine operation
  • Lower operator station sound levels
• Hot air is vented out the front grille, away from the operator.
• Xenoy® molded-in-color hood material is very durable.
  • Excellent impact strength
  • Hides scratches
  • Will not rust or dent
• Distinctive grille, large footrest area, and one-piece fender deck complete the styling package.

Xenoy is a trademark of SABIC Innovative Plastics.

Two headlights give excellent visibility

Headlights are standard equipment.

High-quality headlights make evening work easier and safer:

• Two 27-W bulbs provide excellent lighting for improved visibility during evening operation.
• Headlights are easily operated with a dash-mounted switch.
• Headlights are designed to provide an optimum lighting pattern for mowing and snow removal.

The operator station is designed for operator comfort and convenience in operating all controls. The controls are color coded for easy identification. The X590 does not require a choke lever because the engine has electronic fuel injection (EFI) that automatically provides the correct amount of fuel to the engine for fast and reliable starts.

Comfortable seat

The 53.3-cm (21-in.) high-back seat features distinctive styling and is designed for comfort:

• Contoured design fits the operator’s body to give the most comfortable ride.
• High-back seat provides additional comfort and support for the operator.

Adjustable suspension

The seat suspension is easily adjusted to make the operator comfortable:

• 17.8 cm (7 in.) of seat travel allows the operator to be seated comfortably and operate the controls easily.
• Seat can be easily adjusted fore and aft by the operator while sitting on the seat (15 positions).
• Seat features a suspension that is easily adjusted for the operator's weight and height.
  • Springs provide a smooth ride and will not bottom out.
  • Spring position is adjustable for the operator's weight.
• Seat tilts forward to keep the seating surface out of the weather.
• Tilting the seat forward keeps moisture and the sun off the seat cushion for greater operator comfort.

Tilt steering wheel (X590 Tractor)

NOTE: Tilt steering wheel is not available on model year 2018 and later X584 Tractors.

• Five steering-wheel positions allow the operator to select the most comfortable setting (X590 Tractor)

Rubber foot pads

Rubber foot pads make the operator more comfortable:

• Help insulate operator's feet from vibration
• Attractive styling
• Long-lasting wear surface
• Reduce chance of slippage, even with wet surface

A cup holder and covered toolbox are conveniently located on the fender next to the operator's seat.

Handles on each fender are useful when getting on and off the tractor.

A 12-V outlet is standard equipment and provides a convenient plug-in for electrical equipment.

The one-piece hood opens easily to permit checking and servicing the engine:

• Important service points are located within easy reach.
• A service-interval decal is provided inside the tractor hood for convenience when servicing the tractor.
  • The high-quality engine used in the X500 Series does not require an 8-hour oil and filter change because improvements in manufacturing processes and quality of parts, components, and oils have eliminated the need for the short interval oil change requirement.

The engine fuel and oil filters, the oil check/fill tube, and the oil drain tube are exposed for serviceability when the hood is opened.

 

Exact Adjust ports and onboard deck-leveling tools make precise deck adjustments easy

A mower deck must be level side-to-side and properly adjusted front-to-rear to give the best cutting performance. A removable onboard deck-leveling gauge and a hex-key tool are provided to make adjustment easy. They are securely stored under the tractor seat.

Exact Adjust leveling ports are provided on each side of the operator platform above the mower-level adjusting bolts. With the hex-shaped tool, they provide convenient access to allow quick and easy adjustment of the mower for the best-cut quality of cut.

The Exact Adjust feature is standard on all Select Series™ X300 and X500 Tractors:

• There is no need to reach under the fender deck while making the mower-level adjustment.
• Onboard deck-leveling gauge, Exact Adjust ports, and the hex tool work together.
  • Level the mower deck side to side
  • Set the correct amount of rake (front-to-back deck orientation)
  • Calibrate the cutting height to the cut-height adjusting knob setting
• Exact Adjust simplifies leveling the mower deck if equipped with a Power Flow™ blower.
  • To give the best cut, mower level should be adjusted if alternately mowing with and without blower installed. The Exact Adjust feature makes this easy.

Consult the operator's manual for the correct adjusting procedures for each tractor model. Basic adjusting steps to properly level the mower deck include:

• Park the tractor on a level surface.
• Inflate tires to the correct pressure.
• Consult the label for the cutting-height knob that is located on the console of the machine. This label shows deck-leveling position and location of deck-leveling adjustment points.

• Set mower cutting-height knob to the correct deck-leveling position.
  • For X300 models, use position 2.75
  • For all other models, use position 2.5
• Adjust mower wheels as necessary so they do not contact the ground surface.
• Remove the onboard deck-leveling gauge that is located under the seat.
• Using the Exact Adjust ports and tool, adjust mower deck side-to-side level so the deck-leveling gauge just slips under the left and right lower deck rim at the designated adjustment points. The location of adjustment points will vary slightly between decks.
  • Left- and right-rear adjustment points are under the deck rim near the rear mower wheels, if equipped.
• Adjust mower deck front-to-back level, if necessary.
  • Loosen rear nuts equally on each side of front lift rod.
  • Turn front nut equally on each side clockwise to raise front of mower or counterclockwise to lower it until gauge just slips under the front adjustment point.
  • Tighten rear nuts after adjustment is complete.
• Return the gauge to its storage position. 

 

NOTE: The adjusting tool supplied with the tractor is an 8-mm ball-hex key, part number M162737. The rounded end allows for some misalignment with the bolt as the deck is adjusted.

This durable blade serves as a perfect solution for snow removal and other materials.

 

It is very easy to mount on the tractor which facilitates all year-round usage through the different seasons. To use it, the operator simply pushes a lever from the seat and the blade lowers to the ground. When the task is complete, pulling back the lever will raise it.

The working angle can be changed with a lever from the tractor. This will be especially appreciated in tighter areas when frequently changing direction between left and right.

Clean to the edge with the wide blade

The blade is wider than the tractor to ensure the tractor has good traction on the cleared path and does not compact snow. Even with an angled blade, the operator can clean up to the edge of walls and other obstacles for best results.

Resist impacts and stay comfortable even when hitting obstacles hidden under snow

Demonstration of the unique safety joint: the tractor is slowed down after the impact yet can move enough to reduce the shock on the operator. The blade moves away from the obstacle by moving up.

Function of a traditional blade (upper line) and the unique safety joint (lower line). [1] = pivot point, [2] = hard obstacle, [3] = snow

Many front blades available in the market tilt around a pivoting point close to the ground (see 1.1). When potentially contacting an obstacle (see 1.2), the pivoting blade can barely move at all, increasing impact on the blade, tractor, and operator even more (1.3).

 

The unique joint solution of this blade is smarter by pivoting around a higher spot (2.1). It avoids a harsh impact as the colliding blade edge moves clearly to the rear (2.2), allowing the tractor to slow down more smoothly. Also, the blade will move up if too much snow is present – and even continues to clear off the snow. Once the hard object is overcome, the spring pushes the blade back to the original position. This all results in more comfort of the operator, better uptime of the blade and tractor together with cost effective snow removal without backing up and rehitting the obstacle attempting to clear snow on it.

Attaching to the tractor in three seconds

To attach the blade to the tractor, simply raise it from ground; hook it into the quick-hitch and lock it. Although it can stay on, taking the mower deck off and using rear wheel weights on the tractor is recommended. For snow applications, snow chains are suggested. Both the weights and the chains are available through John Deere Parts.

Compatibility and required mounting hardware

A John Deere dealer can identify which models are compatible with this broom and order the required mounting hardware.

Further blades, brooms, and snow throwers

The following chart shows the available options for John Deere Riding Lawn Equipment and suggests which solution might be the best in each case. The entire description above applies to the blade with 125-cm (49-in.) quick-hitch. If the tractor is equipped with driveline and corresponding quick-hitch, a tractor with this quick-hitch can carry either the blade or the 120-cm (47-in.) broom.

	Blade -117cm (46 in.) for X100s -44-in. (112-cm) for X300s -48-in. (122-cm) for X500s	Blade with quick-hitch 125 cm (49 in.)	Broom with quick-hitch 120 cm (47 in.)	Snow blower -44 in. (112 cm) for X100s -44 in. (112 cm) for X300s -47 in. (119 cm) for X500s
Cleaning sideways			x
Moving light snow, mulch	x	x	x
Moving heavy snow	x	(x)		x
Notes	Bolts on tractor. Must remove mower deck to use.	Uses quick-hitch	Uses quick-hitch

Model year 2015 (SN 100,001-110,000) X590 Tractors are not compatible with SAB00724 Front Blade and SAB00726 Rotary Broom.

Model year 2015 (SN 100,001-110,000) X590 Tractors are not compatible with SAB00724 Front Blade and SAB00726 Rotary Broom.

The front quick hitch with drive increases tractor versatility.

Compatibility Information

 

SAB00922

For LR135, LR175, X110, X120, X125, X130R, X135R, X140, X145, X155R, X165, X300, X300R, X304, X305R, X320, X534, and X540 Tractors. Required for SAB00726 rotary broom.

Increases machine versatility.

Compatibility Information

 

SAB00720

For X120, X125, X135R, X140, X145, X155R, X165, X300, X300R, X304, X305R, X320, X534, and X540 Tractors.

44-mm (1-7/8-in.) hitch ball attaches to drawbar or rear hitch to allow towing. 19-mm (0.75-in.) diameter post thread is provided.  

 

The hitch ball is available through Parts.

Every John Deere customer who owns a riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes.

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak™ or ZTrak™ mower not to exceed 250 lb (113 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck.

• Cart has a premium molded, high-density polyethylene box construction.
• Compression molding process allows polyethyl­ene to be the optimum thickness in all areas for superior strength and durability.
• Polyethylene body will not rust or dent; it stays looking new longer.
• 0.75-in. (2-cm) x 2-in. (5-cm) stake pockets are molded in to make the addition of side extensions easy.
• Two vertical 0.75-in. (2-cm) molded channels on each side allow easy use of dividers to separate the box into two or three compartments.
• Ribs in the box bottom add strength and prevent the shovel from hitting bolts when emptying the cart.
• Sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.
• Styling is compatible with other John Deere equipment.
• Pneumatic tires provide turf tread for good flotation, shock absorption, and minimal rolling resistance.

Wheels

Wheels are mounted on a solid, one-piece axle for durability.
 
Iron and Oilite® wheel bearings with grease fittings provide lubrication for long life.

The pneumatic tires offer the following:

• Good flotation
• Minimal rolling resistance
• Shock absorption

Sloped tailgate

A sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.

Tractor hitch

A large-diameter hitch pin provides plenty of strength:

• Fast, easy attachment to the tractor hitch
• Spring pin to ensure the pin stays in place

Tilt latch

An easy-to-use spring-loaded dump latch allows tilting the box for easier unloading. Steep dump angle makes emptying the cart easier.

Specifications

 

Box capacity
Heaped, m3 (cu ft)	7 (0.20)
Struck, m3 (cu ft)	5.6 (0.16)
Maximum load, kg (lb)	450* (204)
Box dimensions
Width, cm (in.)	84 (33)
Length, cm (in.)	114 (45)
Depth, cm (in.)	27 (10.5)
Box construction	Molded
Material	High-density polyethylene (HDPE)**
Tailgate	None, sloped
Pneumatic tires	2 ply
Size	13x4x6
Tread design	Turf
Recommended inflation pressure	207 kPa (30 psi)
Wheel bearings	Iron/Oilite®
Grease fittings on wheels	Yes
Axle diameter, cm (in.)	1.905 (0.750)
Ground clearance, cm (in.)	14.3 (5.62)
Width, overall, cm (in.)	86.4 (34)
Hitch pin	Pin/spring clip
Dump angles, degrees	55
Maximum tongue weight, kg (lb)	25 (55)
Shipping weight with carton, kg (lb)	31 (68)
Net weight, kg (lb)	29 (65)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower not to exceed 113 kg (250 lb).
**High-density polyethylene is compression molded for optimum thickness in all areas and maximum durability.

Oilite is a trademark of Beemer Precision Incorporated.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

7P Poly Utility Cart
Order number: MCZLP2193500

Every owner of a John Deere riding lawn and garden product has a potential need for a high-quality, affordable utility cart.

Utility carts can be used to haul a variety of materials:

• Firewood
• Lawn debris
• Sand
• Dirt
• Mulch
• Garden tools
• Plants and bushes

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment:

• Large 295-kg (650-lb) capacity
• 283-L (10-cu ft) heavy duty, 6.4-mm (0.25-in.) thick poly bed
• Won't dent or rust
• 15x6 tubeless pneumatic tires with turf tread for maximum traction
• Easy hands-free foot pedal dump release
• Steep dump angle for complete emptying

Ordering information
Please contact your local John Deere dealer for availability and pricing information.

10P Utility Cart
Order number: MCZLPPCT10JD

Haul a variety of materials. Welded steel box construction.

Compatibility Information

 

BM24601

For X125, X130R, X135R, X140, X145, X155R, X165, X300, X300R, X304, X305R, X320, X740, X748, X749, X750, X754, and X758 Tractors. Must order in multiples of two. The loaded weight of the cart should never exceed the weight of the tractor plus the operator.

Haul a variety of materials. Welded stell box construction.

Compatibility Information

 

BM24602

For X320, X534, X540, X740, X748, X749, X750, X754, and X758. Compatible with GT, GX, X500 M-T, X700 and similar-sized lawn and garden tractors. The loaded weight of the cart should never exceed the weight of the tractor plus the operator.

This 80-kg (175-lb) pull-type broadcast spreader is designed for homeowner use:

• The polyethylene hopper will not dent or rust.
• All stainless-steel interior hardware, shaft, and agitator help to prevent corrosion.
• Large pneumatic turf tires ensure a positive drive and smooth operation.
• High-speed, 6:1 reduction glass-filled nylon gears provide the widest spread pattern at the slowest speeds.
• Fully enclosed gearbox eliminates downtime and maintenance.
• Autoflow feature stops the flow of materials - automatically - to prevent burns.
• Directional spread-pattern control feature provides positive shutoff along sidewalks and driveways.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

80-kg (175-lb) Tow-Behind Spreader

Order number: MCZLPBS36JD0

The Power Flow chute is required, along with the high-performance Power Flow blower, to use the 3-bag Power Flow MCS. The chute includes a convenient handle and a fill indicator that tells the operator when the bags are getting full. 

 

One chute works with several tractor applications. Trim lines on the chute are referenced in the instructions so the chute can be cut to the proper length for the tractor/mower application.

Compatibility Information

 

BM21682

The chute can be used with 48C/48X, 54C/54X, 152-cm (60-in.) 7-Iron™, 62C/62X, and 62D Mowers.

The Power Flow chute is required, along with the high-performance Power Flow blower, to use the 2-bag Power Flow material collection system. The chute includes a convenient handle and a fill indicator that tells the operator when the bags are getting full.

One chute works with several vehicle applications. Trim lines on the chute are referenced in the instructions so the chute can be cut to the proper length for the vehicle/mower application.

Compatibility Information

BM21681

For 48C, 48X, 54C, or 54X Series Blowers.

The 250-L (7-bu) hopper provides an efficient means of collecting grass clippings and leaves using either the cut-and-throw rear bagger or the Power Flow™ material collection system (MCS). The hopper design provides modern styling, great bagging performance, cleaner operation, and easy-to-empty bags.

 

The 250-L (7-bu) MCS hopper features:

• 250-L (7-bu) capacity
• Easy-to-attach lower chute (ordered separately)
• Handle on chute
• Air exhaust duct
• Convenient spring latch
• Airflow fill indicator
• Quik-Tatch mounting
• Sealed hopper top
• Loose-knit bags available

Compatibility Information

 

BM24508

For X300, X300 less deck, X305R/107 cm (42 in.), X310 less deck, X320, X320 less deck, X534, X534 less deck and X540. 38X requres BM20982 97 cm (38 in.) cut/throw chute, 42X requires BM22594 107 cm (42 in.) cut/throw chute, 48x requires BM21681 48/54 Power Flow chute and BM24470 122-cm (48-in.) Power Flow blower, 54X requires BM21681 48/54 Power Flow chute and BM24471 54 Power Flow blower.

The 500-L (14-bu), 3-bag Power Flow™ MCS increases the versatility of the X500 Multi-Terrain Tractors and the GT and GX series garden tractors equipped with a 122-cm (48-in.) or 137-cm (54-in.) convertible or Edge™ Xtra Mower (48X, 54X) and high performance Power Flow blower. The large 500-L (14-bu) capacity means the operator can collect a large area of grass or leaves before needing to stop to empty the bags.

Compatibility Information

 

BM24510

For X534 and X540 Tractors. 48X requires BM21682 48/54 Power Flow chute and BM24470 48 Power Flow blower. 54X requires BM21682 48/54 Power Flow chute and BM24471 54 Power Flow blower.

A loose-knit bag is available as an option for use with 247-L (7-bu) cut-n-throw rear baggers and Power Flow™ baggers:

• Two loose-knit bags are required.
• The loose-knit bag allows more air to flow through and provide more complete bag filling in wet and heavy grass conditions.

The high-performance (HP) Power Flow blower assembly for the 122-cm (48-in.) Accel Deep™ Mower is used with the hopper and chute to provide a very effective material collection system. A hopper and chute must be ordered separately to complete this material collection system.

The high-performance (HP) Power Flow blower assembly for the 137-cm (54-in.) Accel Deep™ Mower is used with the hopper and chute to provide a very effective material collection system. A hopper and chute must be ordered separately to complete this material collection system.

LG265 home maintenance kit

Home maintenance kits are a handy and convenient way for dealers to supply a customer with the maintenance-interval parts as specified in their operator's manual.

 

The LG265 home maintenance kit includes the following:

 

Quantity	Description
1	Engine oil filter
2	Engine oil quart
1	Fuel filter
1	Air filter element
1	Air filter element foam
2	Spark plug

Battery charger and maintainer, 3 pin UK plug

Battery charger and maintainer, 3 pin UK plug

NOTE: The photo above shows the earlier AM136691 winter grille cover on a pre-2014 X300 Tractor. AM145350 winter grille cover replaces AM136691. It is similar in appearance and designed for use with the earlier hoods as well as the 2014 and later hoods used on X300 Series Tractors (SN 280,001-) with the newer styling.

 

Winter grille covers are available as an accessory for Select Series™ X300 and air-cooled X500 Multi-
Terrain Tractors:

• Faster engine warm-up and higher winter operating temperature
• Prevents the engine carburetor from icing-up while blowing or blading snow, or
  during similar applications, when operating in certain cold weather conditions
• Elastic straps make installation and removal quick and easy

*The winter grille cover is recommended only for air-cooled tractors; use of the winter grille cover on a
liquid-cooled tractor may cause the engine to overheat, which will cause the power take-off (PTO) to disengage.

NOTE: To avoid engine damage, the winter grille cover must be removed when outside temperature reaches 40 degrees F (4 degrees C) or higher.

The purpose of the winter grille cover is to seal the side vents on the hood; they need to be blocked completely. The cover must be aligned properly to accomplish this. If the sides are not sealed, carburetor icing may still be a problem.

Symptoms of carburetor icing:

• While blowing snow in freezing temperatures, the engine gradually loses power, emits black smoke from exhaust, misses, stalls, and fouls spark plugs.
• If the tractor is left outside in freezing temperatures after blowing snow, the choke may not move when trying to start the engine.
• Engine will start after sitting outside in freezing temperatures, but runs poorly and lacks power; black smoke may be emitted through the exhaust.

The brush guard adds a distinctive appearance to the tractor and protects the front of the tractor from damage.

By removing one spring clip and pin, the brush guard may be lowered to permit opening the hood.

Compatibility Information

BM23057

For X300, X300R, X304, X305R, X310, X320, X534, and X540.

Cover provides heavy-duty protection for Select Series™ X300, X500, and X700 Tractors.

Features include:

• Wipe-clean reinforced bottom around mower deck
• Easy-on side handles makes snugging down cover a snap
• Dual reinforced air vents let air circulate and help prevent ballooning in wind
• Interior lining and integrated muffler heat shield
• Heavy-duty fabric will not shrink or stretch and is coated for maximum water resistance
• Easy-on split back for fast fitting and easy access after installation
• Handy storage pocket reverses into an attractive storage case
• Two-year warranty

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

Protective cover (large deluxe)

Order number: MCALP9364700

Features include:

• Dual vents let air circulate and help prevent ballooning in wind
• Elastic shock cord in bottom hem for a quick, custom-like fit
• Coated fabric for maximum water protection
• One-year warranty

Cover provides all-season protection for X100 Series and Select Series™ X300 Series Tractors.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Protective cover (standard)

Order number: MCALP9391700

The BM26238 dry-condition kit, 48A is available for 48A Accel Deep Mower Decks used on model year 2016 and later X300 and X500 Select Series™ Tractors and Residential ZTrak™ Mowers. The 48A dry-condition kit will also work with any X700 Signature Series Tractor (model year 2013 and later) that is equipped with a 48A Mower Deck.

The dry-condition kit will reduce the amount of blowout around the mower deck when side discharging, mulching, or bagging in dry grass and leaf conditions. For optimum mowing performance in lush-grass conditions, the dry-condition kit baffles may be removed.

The BM26239 dry-condition kit, 54A is available for 54A Accel Deep Mower Decks used on model year 2016 and later X300 and X500 Select Series™ Tractors and Residential ZTrak™ Mowers.

The dry-condition kit will reduce the amount of blowout around the mower deck when side discharging, mulching, or bagging in dry grass and leaf conditions. For optimum mowing performance in lush-grass conditions, the dry-condition kit baffles may be removed.

Leveling gauge allows quick and accurate mower deck leveling and cutting height adjustment.

Can be used for:

• Lawn tractors
• Lawn and garden tractors
• Riding mowers
• Front mowers
• Commercial walk-behind mowers
• Zero-turn-radius mowers

MulchControl advantages and benefits

The MulchControl attachment for the 48A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:

• A beautiful looking lawn
• Grass clippings not blown onto the operator, driveways, or flower beds
• Less fertilizer use
• Elimination of the effort needed to dispose of clippings

How MulchControl works

MulchControl is an innovative, simple design that is easy to use and maintain:

• The MulchControl attachment includes baffles to control the flow of material under the deck.
  • The left mower blade area is completely enclosed and optimized for mulching, thus will mulch even when the mower is in the side-discharge mode.
  • Baffles around the center and right blades are optimized for mulching when the discharge baffle is closed.

• The MulchControl handle is located on top of the mower deck and used to open and close the discharge baffle.
  • The operator is required to get off of the machine in order to engage or disengage mulch mode.
• Changing from mulching to side discharge or vice versa takes only a few seconds.

MulchControl is well-suited to the following mowing situations:

• Usually mulch, but side discharge when grass gets too long
• Usually side-discharge, but would like to be able to close the chute to control clippings
• Always mulch a main lawn, but often side discharge secondary lawns
• Bag clippings, but want to go farther before emptying bags

MulchControl puts the operator in control of the clippings. Now the operator can have all the benefits of mulching with the ability to easily change to side discharge or bagging when needed.

MulchControl limitations

While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:

• When cutting strong southern grasses
• When cutting in wet, high-growth conditions
• When optimum bagging and lawn clean-up is desired

MulchControl advantages and benefits

The MulchControl attachment for the 54A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:

• A beautiful looking lawn
• Grass clippings not blown onto the operator, driveways, or flower beds
• Less fertilizer use
• Elimination of the effort needed to dispose of clippings

How MulchControl works

MulchControl is an innovative, simple design that is easy to use and maintain:

• The MulchControl attachment includes baffles to control the flow of material under the deck.
  • The left mower blade area is completely enclosed and optimized for mulching, thus will mulch even when the mower is in the side-discharge mode.
  • Baffles around the center and right blades are optimized for mulching when the discharge baffle is closed.

• The MulchControl handle is located on top of the mower deck and used to open and close the discharge baffle.
  • The operator is required to get off of the machine in order to engage or disengage mulch mode.
• Changing from mulching to side discharge or vice versa takes only a few seconds.

MulchControl is well-suited to the following mowing situations:

• Usually mulch, but side discharge when grass gets too long
• Usually side-discharge, but would like to be able to close the chute to control clippings
• Always mulch a main lawn, but often side discharge secondary lawns
• Bag clippings, but want to go farther before emptying bags

MulchControl puts the operator in control of the clippings. Now the operator can have all the benefits of mulching with the ability to easily change to side discharge or bagging when needed.

MulchControl limitations

While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:

• When cutting strong southern grasses
• When cutting in wet, high-growth conditions
• When optimum bagging and lawn clean-up is desired

Compatibility Information

 

BM24426

For model year 2013- X700 Signature Series Tractors and X500 Multi-Terrain Tractors equipped with 53.3-cm (21-in.) professional two-piece seat.

The 53.3-cm (21-in.) professional two-piece seat, four-bar suspension, and slide are for 2015 and later Signature Series X700 Tractors and X534, X540, and X590 Multi-Terrain Tractors. Key selling features for this seat include:

• Thick seat cushion for lasting comfort, even after a full day of use
• Back of seat can be angled to maximize operator comfort
  •  Convenient lever on the side of the seat unlocks back of seat to allow positioning
• Includes four-bar suspension and slide for extra comfort that bolts to four mounting holes in tractor fender deck
• BM24426 armrest attachment available as a field-installed option

Optional armrest attachment

 

Armrests increase operator support and comfort, thus reducing fatigue and improving productivity, especially when mowing for extended periods of time. Armrests are adjustable to suit the operator. This armrest attachment is designed for the 53.3-cm (21-in.) professional two-piece seat.

Compatibility

BM25346 53.3-cm (21-in.) professional two-piece seat is a field-installed attachment and compatible as follows:

• Select Series™ X500 Series Multi-Terrain Tractors
• X700 Signature Series Tractors

One or two 22.7-kg (50-lb) cast-iron weights may be installed on each rear wheel to provide extra traction and stability.

Features include:

• Weights are made of durable cast iron and painted John Deere yellow.
• Weights may be installed with the wheel in either the narrow or wide position.
• These weights may be used on both two-wheel-steer and all-wheel-steer tractors.
• To stack the weights and install two on a wheel, two 12.7x203-mm (1/2x8-in.) bolts are required per wheel (not furnished).
• X700 Special Edition Tractors (model year 2012 and prior) and four-wheel drive X700 Signature Series Tractors require a BM21497 wheel weight adapter ring on each rear wheel on which weights are to be installed.

Compatibility Information

BM17972

X700 Special Edition Tractors (model year 2012 and prior) and X700 four-wheel drive Signature Series Tractors require a BM21497 wheel weight adapter ring on each rear wheel on which weights are to be installed.

One 22.7-kg (50-lb) plastic-shell rear wheel weight may be installed on each rear wheel to provide extra traction and stability.

The outer shell is molded of tough polyethylene plastic and filled with a heavy, granular material that contains a high percentage of iron. A bonding substance is added to hold the material together so that it will remain intact, even if the shell is damaged.

Multiple stacking is not recommended.

Overall width of the tractor will be increased by approximately 2 in. (51 mm) when weights are installed.

Compatibility:

• 23x10.5-12 and 24x12-12 wheels and tires in narrow position only
• 26x12-12 wheels and tires

Weights are packaged one per carton, with necessary hardware for installation on a wheel.

X700 Special Edition Tractors (model year 2012 and prior) and X738, X739, and X758 Signature Series Tractors require a BM21497 wheel weight adapter ring on each rear wheel on which weights are to be installed.

NOTES:

1. Plastic rear wheel weight comes with necessary hardware for installation.
2. X700 Series Special-Edition Tractors and the X758 Tractor require an additional BM21497 special-edition weight adapter for each rear wheel on which weights are to be installed.

For 22.7-kg (50-lb) cast-iron wheel weights on 23x10.50-12 or 24x12-12 rear tires:

 

BM17985 - for mounting one 22.7-kg (50-lb) weight

BM17977 - for mounting two 22.7-kg (50-lb) weights

For 22.7-kg (50-lb) cast-iron wheel weights on 26x12-in. rear tires:

 

BM17977 - for mounting one 22.7-kg (50-lb) weight

BM18101 - for mounting two 22.7-kg (50-lb) weights 

For 32 ­kg (70 ­lb) starter cast-iron wheel weight on 26x12-12-in. rear tires:

 

BM18089 - for mounting 32 kg (70 lb) starter weight

For 32 kg (70 lb) starter and 22.7-kg (50-lb) cast-iron weight(s):

 

BM17977 - for mounting one 32 kg (70 lb) starter and one 22.7-kg (50-lb) weight

BM18101 - for mounting one 32 kg (70 lb) starter and two 22.7-kg (50-lb) weights

A - one (1) UC13499 and one (1) BM17972 weight
B - one (1) UC13499 and two (2) BM17972 weights

Four-wheel-steer tractors

NOTE:  Plastic wheel weight is not compatible with four-wheel-steer tractors.

For 22.7-kg (50-lb) cast-iron wheel weight on 26x10.50-12 tires:

 

BM18094 - for mounting one 22.7-kg (50-lb) weight

BM17977 - for mounting two 22.7-kg (50-lb) weights

NOTES: Plastic rear wheel weight comes with necessary hardware for installation.

X Series Special-Edition Tractors require an additional BM21497 special-edition weight adapter for each rear wheel on which weights are to be installed.

For 50-lb cast-iron wheel weights on 26x12-in. rear tires:

 

BM17977 For mounting one 50 lb weight

BM18101 For mounting two 50 lb weights

For 72-lb starter cast-iron wheel weight on 26x12.-12-in. rear tires:

 

BM18089     For mounting 72-lb starter weight

For 72-lb starter and 50-lb cast-iron weight(s):

 

BM17977 For mounting one 72-lb starter and one 50-lb weight

BM18101 For mounting one 72-lb starter and two 50-lb weights

 

Four-wheel-steer tractors

NOTE:Plastic wheel weight is not compatible with four-wheel-steer tractors.

For 50-lb cast-iron wheel weight on 26x10.50-12 tires:

 

BM18094 For mounting one 50-lb weight

BM17977 For mounting two 50-lb weights

The 19.1-kg (42-lb) Quik-Tatch can be used to counterbalance a heavy front or rear attachment and/or provide greater stability, especially when operating on hills.

 

This weight is constructed of cast iron and weighs approximately 19.1-kg (42-lb).

 

Some vehicles have built-in front and/or rear weight brackets to hang the weights on; others require a weight bracket that must be ordered separately.

X400/X500 Heavy-Duty Garden Tractors and X700 Series Tractors require the following parts when weights are installed on the front of the tractor:

• One  M147986 weight retaining rod (Parts)
• Two  M40461 spring clip (Parts)

Compatibility Information

 

R66949

For 1400/1500 Front Mowers, X300 Series Tractors, X500 Series Tractors, and X700 Series Tractors.

The 19-kg (42-lb) Quik-Tatch can be used to counterbalance a heavy front or rear attachment and/or provide greater stability, especially when operating on hills.

 

This weight is constructed of cast iron and weighs approximately 19-kg (42-lb).

 

Some vehicles have built-in front and/or rear weight brackets to hang the weights on; others require a weight bracket that must be ordered separately.

X400/X500 Heavy-Duty Garden Tractors and X700 Series Tractors require the following parts when weights are installed on the front of the tractor:

• One  M147986 weight retaining rod (Parts)
• Two  M40461 spring clip (Parts)

One 13.6-kg (30-lb) cast-iron weight may be installed on each front wheel for additional stability when operating on hillsides or with heavy rear equipment.

Requirements:

• Mounting may require drilling two holes in the wheel rim.
• BM17978 mounting hardware kit is required for each weight.

NOTE: Front wheel weights are not available for special-edition tractors because the styled front  wheel design does not have appropriate holes for mounting the wheel weights and no adapter is available.

Compatibility information

 

BM17964

Not for four-wheel drive tractors or special-edition tractors.

One pair of chains is included in each bundle.

Chains are recommended for extra traction when using attachments such as a snow blower or front blade.